Home / Products / Industrial Compressors
SH series — 14 families, one screw platform
PM variable-frequency and fixed-speed screw compressors, single- and two-stage, 4-in-1 combined stations, laser-cutting packages and low-pressure lines: 7.5–450 kW, 0.2–1.55 MPa. Click any unit to enlarge; use the selection table below to find your model.
Series overview
Choose the family, then the model
SH-AH
SH-AH
Permanent-magnet variable-frequency screw compressors with centrifugal cooling fan; single-stage compression for general plant air.
SH-AHT
SH-AHT
Two-stage PM variable-frequency machines: lower specific power at continuous full load.
SH-JH
SH-JH
Fixed-frequency single-stage screw compressors with centrifugal fan — robust base-load duty.
SH-JHT
SH-JHT
Fixed-frequency two-stage line up to 450 kW, water-cooled at the largest frames.
SH-A
SH-A
PM variable-frequency single-stage compressors with axial cooling fan; compact frames from 7.5 kW.
SH-AT
SH-AT
Two-stage PM variable-frequency line with axial fan, up to 450 kW water-cooled.
SH-J
SH-J
Fixed-frequency single-stage screw compressors with axial fan for steady demand.
SH-JT
SH-JT
Fixed-frequency two-stage compressors with axial fan; high-efficiency continuous duty.
SH-AZ
SH-AZ
4-in-1 combined station: screw compressor + receiver + refrigerated dryer + filters on one base.
SH-JZ
SH-JZ
Fixed-frequency 4-in-1 combined air station for workshops and small plants.
SH-AZG
SH-AZG
Combined packages dedicated to laser cutting: higher pressure, dry clean air, 4-in-1 / 5-in-1 configurations.
SH-JZG
SH-JZG
Fixed-frequency laser-cutting combined packages, 4-in-1 / 5-in-1 high-spec configurations.
SH-ADH
SH-ADH/ADHT
Low-pressure PM variable-frequency screw compressors (single / two-stage) for aeration, conveying and process air.
SH-AD
SH-AD/ADT
Low-pressure PM variable-frequency line with axial fan, 0.2–0.5 MPa duties.
Selection table
All models — filter by series & pressure
Complete SH series data: capacity at each working pressure, noise, cooling, outlet, dimensions and weight.
SH series model data
| Model | kW | MPa | FAD (m³/min) | Noise dB(A) | Cooling | Outlet | L×W×H (mm) | Weight (kg) | Receiver (L) | Configuration | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-30AH | 30 | 0.8 | 1.7-5.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-30AH | 30 | 1 | 1.4-4.1 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-30AH | 30 | 1.25 | 1.2-3.4 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-37AH | 37 | 0.8 | 2.2-6.5 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-37AH | 37 | 1 | 1.8-5.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-37AH | 37 | 1.25 | 1.5-4.5 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-45AH | 45 | 0.8 | 2.4-7.1 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-45AH | 45 | 1 | 2.2-6.3 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-45AH | 45 | 1.25 | 1.7-5.1 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-55AH | 55 | 0.8 | 3.2-9.3 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-55AH | 55 | 1 | 2.5-7.4 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-55AH | 55 | 1.25 | 2.2-6.5 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75AH | 75 | 0.8 | 4.2-12.2 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75AH | 75 | 1 | 3.1-9.1 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75AH | 75 | 1.25 | 2.2-6.5 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-90AH | 90 | 0.8 | 5.2-15.4 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-90AH | 90 | 1 | 4.2-12.2 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-90AH | 90 | 1.25 | 3.6-10.6 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-110AH | 110 | 0.8 | 6.5-19.0 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-110AH | 110 | 1 | 5.2-15.4 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-110AH | 110 | 1.25 | 4.4-13.0 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-132AH | 132 | 0.8 | 7.6-22.3 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-132AH | 132 | 1 | 6.5-19.0 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-132AH | 132 | 1.25 | 5.7-16.7 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-160AH | 160 | 0.8 | 9.5-28.0 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-160AH | 160 | 1 | 8.1-23.8 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-160AH | 160 | 1.25 | 7.5-21.9 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-185AH | 185 | 0.8 | 10.5-31.0 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-185AH | 185 | 1 | 9.7-28.6 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-185AH | 185 | 1.25 | 8.4-24.6 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-200AH | 200 | 0.8 | 11.7-34.5 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-200AH | 200 | 1 | 10.2-30.0 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-200AH | 200 | 1.25 | 8.8-26.0 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-220AH | 220 | 0.8 | 13.2-38.9 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-220AH | 220 | 1 | 11.7-34.4 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-220AH | 220 | 1.25 | 10.1-30.1 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-250AH | 250 | 0.8 | 14.3-42.0 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-250AH | 250 | 1 | 13.2-38.8 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-250AH | 250 | 1.25 | 11.7-34.4 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-280AH | 280 | 0.8 | 15.7-46.1 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-280AH | 280 | 1 | 14.5-42.6 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-280AH | 280 | 1.25 | 12.9-38.0 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-30AHT | 30 | 0.8 | 2.1-6.1 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-30AHT | 30 | 1 | 1.8-5.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-30AHT | 30 | 1.25 | 1.3-4.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-37AHT | 37 | 0.8 | 2.4-7.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-37AHT | 37 | 1 | 2.0-6.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-37AHT | 37 | 1.25 | 1.7-5.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-45AHT | 45 | 0.8 | 3.2-9.3 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-45AHT | 45 | 1 | 2.8-8.2 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-45AHT | 45 | 1.25 | 2.4-6.9 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-55AHT | 55 | 0.8 | 4.2-12.2 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-55AHT | 55 | 1 | 3.2-9.3 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-55AHT | 55 | 1.25 | 2.8-8.3 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-75AHT | 75 | 0.8 | 5.5-16.2 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-75AHT | 75 | 1 | 4.4-13.0 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-75AHT | 75 | 1.25 | 4.0-11.8 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-90AHT | 90 | 0.8 | 6.5-19.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-90AHT | 90 | 1 | 5.4-16.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-90AHT | 90 | 1.25 | 4.2-15.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-110AHT | 110 | 0.8 | 7.9-23.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-110AHT | 110 | 1 | 6.5-19.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-110AHT | 110 | 1.25 | 6.2-18.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-132AHT | 132 | 0.8 | 9.2-27.2 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-132AHT | 132 | 1 | 7.9-23.2 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-132AHT | 132 | 1.25 | 6.8-20.1 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-160AHT | 160 | 0.8 | 11.3-33.3 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-160AHT | 160 | 1 | 9.8-28.8 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-160AHT | 160 | 1.25 | 7.4-27.6 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-185AHT | 185 | 0.8 | 13.5-39.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-185AHT | 185 | 1 | 11.3-33.3 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-185AHT | 185 | 1.25 | 10.4-30.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-200AHT | 200 | 0.8 | 14.6-43.1 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6000 | — | — | |
| SH-200AHT | 200 | 1 | 13.4-39.5 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6000 | — | — | |
| SH-200AHT | 200 | 1.25 | 10.7-31.6 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6000 | — | — | |
| SH-220AHT | 220 | 0.8 | 15.5-45.5 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6500 | — | — | |
| SH-220AHT | 220 | 1 | 14.3-42.0 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6500 | — | — | |
| SH-220AHT | 220 | 1.25 | 12.1-35.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2400 | 6500 | — | — | |
| SH-250AHT | 250 | 0.8 | 18.4-54.0 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2500 | 6600 | — | — | |
| SH-250AHT | 250 | 1 | 16.1-47.4 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2500 | 6600 | — | — | |
| SH-250AHT | 250 | 1.25 | 14.2-41.8 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2250×2500 | 6600 | — | — | |
| SH-280AHT | 280 | 0.8 | 19.6-57.8 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-280AHT | 280 | 1 | 17.3-50.9 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-280AHT | 280 | 1.25 | 14.3-42.2 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-315AHT | 315 | 0.8 | 21.7-63.9 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-315AHT | 315 | 1 | 19.6-57.6 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-315AHT | 315 | 1.25 | 16.0-47.0 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-355AHT | 355 | 0.8 | 25.9-76.4 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-355AHT | 355 | 1 | 20.8-61.2 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-355AHT | 355 | 1.25 | 18.1-53.1 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-30JH | 30 | 0.8 | 5.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-30JH | 30 | 1 | 3.5 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-30JH | 30 | 1.25 | 3.3 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 650 | — | — | |
| SH-37JH | 37 | 0.8 | 6.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-37JH | 37 | 1 | 5.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-37JH | 37 | 1.25 | 4.8 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 720 | — | — | |
| SH-45JH | 45 | 0.8 | 7.1 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-45JH | 45 | 1 | 5.8 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-45JH | 45 | 1.25 | 5.6 | 65±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1400×1000×1510 | 740 | — | — | |
| SH-55JH | 55 | 0.8 | 9.3 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-55JH | 55 | 1 | 6.9 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-55JH | 55 | 1.25 | 6.7 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75JH | 75 | 0.8 | 12.2 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75JH | 75 | 1 | 9.2 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-75JH | 75 | 1.25 | 9.0 | 68±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1700 | — | — | |
| SH-90JH | 90 | 0.8 | 15.4 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-90JH | 90 | 1 | 11.2 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-90JH | 90 | 1.25 | 11.0 | 70±2 | Air-cooled (centrifugal fan) | G2 | 2200×1380×1800 | 1800 | — | — | |
| SH-110JH | 110 | 0.8 | 19.0 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-110JH | 110 | 1 | 14.3 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-110JH | 110 | 1.25 | 14.0 | 70±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2400×1570×1900 | 2100 | — | — | |
| SH-132JH | 132 | 0.8 | 22.3 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-132JH | 132 | 1 | 18.7 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-132JH | 132 | 1.25 | 18.5 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 2400×1570×1900 | 2200 | — | — | |
| SH-160JH | 160 | 0.8 | 28.0 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-160JH | 160 | 1 | 21.2 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-160JH | 160 | 1.25 | 21.0 | 72±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 2600 | — | — | |
| SH-185JH | 185 | 0.8 | 30.8 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-185JH | 185 | 1 | 27.0 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-185JH | 185 | 1.25 | 21.2 | 75±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1700×2150 | 3000 | — | — | |
| SH-200JH | 200 | 0.8 | 34.5* | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-200JH | 200 | 1 | 30.6 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-200JH | 200 | 1.25 | 27.0 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4200 | — | — | |
| SH-220JH | 220 | 0.8 | 38.1 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-220JH | 220 | 1 | 31.0* | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-220JH | 220 | 1.25 | 28.8 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 4300 | — | — | |
| SH-250JH | 250 | 0.8 | 42.0 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-250JH | 250 | 1 | 30.7 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-250JH | 250 | 1.25 | 30.3 | 78±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 4800 | — | — | |
| SH-280JH | 280 | 0.8 | 46.1 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-280JH | 280 | 1 | 41.0 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-280JH | 280 | 1.25 | 37.0 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4000×2240×2400 | 4850 | — | — | |
| SH-30JHT | 30 | 0.8 | 6.1 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-30JHT | 30 | 1 | 5.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-30JHT | 30 | 1.25 | 4.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 800 | — | — | |
| SH-37JHT | 37 | 0.8 | 7.2 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-37JHT | 37 | 1 | 6.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-37JHT | 37 | 1.25 | 5.0 | 62±2 | Air-cooled (centrifugal fan) | G1 1/2 | 1580×1040×1560 | 820 | — | — | |
| SH-45JHT | 45 | 0.8 | 9.3 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-45JHT | 45 | 1 | 8.2 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-45JHT | 45 | 1.25 | 6.9 | 63±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1750 | — | — | |
| SH-55JHT | 55 | 0.8 | 12.2 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-55JHT | 55 | 1 | 9.3 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-55JHT | 55 | 1.25 | 8.3 | 65±2 | Air-cooled (centrifugal fan) | G2 | 2350×1380×1800 | 1800 | — | — | |
| SH-75JHT | 75 | 0.8 | 16.2 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-75JHT | 75 | 1 | 13.0 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-75JHT | 75 | 1.25 | 11.8 | 65±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2350×1420×1800 | 1850 | — | — | |
| SH-90JHT | 90 | 0.8 | 19.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-90JHT | 90 | 1 | 16.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-90JHT | 90 | 1.25 | 15.0 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1570×1900 | 2400 | — | — | |
| SH-110JHT | 110 | 0.8 | 23.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-110JHT | 110 | 1 | 19.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-110JHT | 110 | 1.25 | 18.2 | 68±2 | Air-cooled (centrifugal fan) | G2 1/2 | 2600×1620×1900 | 2500 | — | — | |
| SH-132JHT | 132 | 0.8 | 27.2 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-132JHT | 132 | 1 | 23.2 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-132JHT | 132 | 1.25 | 20.1 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 3800 | — | — | |
| SH-160JHT | 160 | 0.8 | 33.3 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-160JHT | 160 | 1 | 28.8 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-160JHT | 160 | 1.25 | 27.6 | 70±2 | Air-cooled (centrifugal fan) | DN80 | 3180×1695×2150 | 4000 | — | — | |
| SH-185JHT | 185 | 0.8 | 39.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-185JHT | 185 | 1 | 33.3 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-185JHT | 185 | 1.25 | 30.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 3500×1750×2350 | 5500 | — | — | |
| SH-200JHT | 200 | 0.8 | 43.1 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6000 | — | — | |
| SH-200JHT | 200 | 1 | 39.5 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6000 | — | — | |
| SH-200JHT | 200 | 1.25 | 31.6 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6000 | — | — | |
| SH-220JHT | 220 | 0.8 | 45.5 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6500 | — | — | |
| SH-220JHT | 220 | 1 | 42.0 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6500 | — | — | |
| SH-220JHT | 220 | 1.25 | 35.7 | 72±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2400 | 6500 | — | — | |
| SH-250JHT | 250 | 0.8 | 54.0 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2500 | 6600 | — | — | |
| SH-250JHT | 250 | 1 | 47.4 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2500 | 6600 | — | — | |
| SH-250JHT | 250 | 1.25 | 41.8 | 75±2 | Air-cooled (centrifugal fan) | DN125 | 4000×2240×2500 | 6600 | — | — | |
| SH-280JHT | 280 | 0.8 | 57.8 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-280JHT | 280 | 1 | 50.9 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-280JHT | 280 | 1.25 | 42.2 | 75±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 8500 | — | — | |
| SH-315JHT | 315 | 0.8 | 63.9 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-315JHT | 315 | 1 | 57.6 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-315JHT | 315 | 1.25 | 47.0 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9000 | — | — | |
| SH-355JHT | 355 | 0.8 | 76.4 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-355JHT | 355 | 1 | 61.2 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-355JHT | 355 | 1.25 | 53.1 | 78±2 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | 9500 | — | — | |
| SH-400JHT | 400 | 0.8 | 81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400JHT | 400 | 1 | 76.4 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400JHT | 400 | 1.25 | 62.2 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-450JHT | 450 | 0.8 | 91.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450JHT | 450 | 1 | 81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450JHT | 450 | 1.25 | 76.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-7.5A | 7.5 | 0.8 | 0.4-1.1 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 130 | — | — | |
| SH-7.5A | 7.5 | 1 | 0.3-0.9 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 130 | — | — | |
| SH-7.5A | 7.5 | 1.25 | 0.3-0.7 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 130 | — | — | |
| SH-11A | 11 | 0.8 | 0.6-1.8 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 215 | — | — | |
| SH-11A | 11 | 1 | 0.5-1.5 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 215 | — | — | |
| SH-11A | 11 | 1.25 | 0.4-1.1 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 215 | — | — | |
| SH-15A | 15 | 0.8 | 0.8-2.4 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 220 | — | — | |
| SH-15A | 15 | 1 | 0.7-2.2 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 220 | — | — | |
| SH-15A | 15 | 1.25 | 0.6-1.8 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 220 | — | — | |
| SH-22A | 22 | 0.8 | 1.2-3.5 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 280 | — | — | |
| SH-22A | 22 | 1 | 1.0-3.1 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 280 | — | — | |
| SH-22A | 22 | 1.25 | 0.8-2.6 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 280 | — | — | |
| SH-30A | 30 | 0.8 | 1.7-5.0 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 295 | — | — | |
| SH-30A | 30 | 1 | 1.4-4.1 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 295 | — | — | |
| SH-30A | 30 | 1.25 | 1.2-3.4 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 295 | — | — | |
| SH-37A | 37 | 0.8 | 2.2-6.5 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 430 | — | — | |
| SH-37A | 37 | 1 | 1.8-5.2 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 430 | — | — | |
| SH-37A | 37 | 1.25 | 1.5-4.5 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 430 | — | — | |
| SH-45A | 45 | 0.8 | 2.4-7.1 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 490 | — | — | |
| SH-45A | 45 | 1 | 2.2-6.3 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 490 | — | — | |
| SH-45A | 45 | 1.25 | 1.7-5.1 | 67±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 490 | — | — | |
| SH-55A | 55 | 0.8 | 3.2-9.3 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 950 | — | — | |
| SH-55A | 55 | 1 | 2.8-8.0 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 950 | — | — | |
| SH-55A | 55 | 1.25 | 2.2-6.5 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 950 | — | — | |
| SH-75A | 75 | 0.8 | 4.2-12.2 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1000 | — | — | |
| SH-75A | 75 | 1 | 3.1-9.1 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1000 | — | — | |
| SH-75A | 75 | 1.25 | 2.8-8.0 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1000 | — | — | |
| SH-90A | 90 | 0.8 | 5.2-15.4 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-90A | 90 | 1 | 4.2-12.2 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-90A | 90 | 1.25 | 3.6-10.6 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-110A | 110 | 0.8 | 6.5-19.0 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-110A | 110 | 1 | 5.2-15.4 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-110A | 110 | 1.25 | 4.4-13.0 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-132A | 132 | 0.8 | 7.6-22.3 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-132A | 132 | 1 | 6.5-19.0 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-132A | 132 | 1.25 | 5.7-16.7 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-160A | 160 | 0.8 | 9.5-28.0 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-160A | 160 | 1 | 8.1-23.8 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-160A | 160 | 1.25 | 7.5-21.9 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-185A | 185 | 0.8 | 10.5-31.0 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-185A | 185 | 1 | 9.7-28.6 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-185A | 185 | 1.25 | 8.4-24.6 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-200A | 200 | 0.8 | 11.7-34.5 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-200A | 200 | 1 | 10.2-30.0 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-200A | 200 | 1.25 | 8.8-26.0 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-220A | 220 | 0.8 | 13.2-38.9 | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-220A | 220 | 1 | 11.7-34.4 | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-220A | 220 | 1.25 | 10.1-30.1 | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-250A | 250 | 0.8 | 14.3-42.0 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-250A | 250 | 1 | 13.2-38.8 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-250A | 250 | 1.25 | 11.7-34.4 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-280A | 280 | 0.8 | 15.7-46.1 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-280A | 280 | 1 | 14.5-42.6 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-280A | 280 | 1.25 | 12.9-38.0 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-15AT | 15 | 0.8 | 1.0-2.9 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-15AT | 15 | 1 | 0.8-2.4 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-15AT | 15 | 1.25 | 0.7-2.1 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-22AT | 22 | 0.8 | 1.4-4.2 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-22AT | 22 | 1 | 1.2-3.5 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-22AT | 22 | 1.25 | 0.8-2.6 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-30AT | 30 | 0.8 | 2.1-6.1 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-30AT | 30 | 1 | 1.8-5.2 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-30AT | 30 | 1.25 | 1.3-4.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-37AT | 37 | 0.8 | 2.4-7.2 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-37AT | 37 | 1 | 2.0-6.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-37AT | 37 | 1.25 | 1.7-5.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-45AT | 45 | 0.8 | 3.2-9.3 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-45AT | 45 | 1 | 2.8-8.2 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-45AT | 45 | 1.25 | 2.4-6.9 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-55AT | 55 | 0.8 | 4.2-12.2 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-55AT | 55 | 1 | 3.2-9.3 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-55AT | 55 | 1.25 | 2.8-8.3 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-75AT | 75 | 0.8 | 5.5-16.2 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-75AT | 75 | 1 | 4.4-13.0 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-75AT | 75 | 1.25 | 4.0-11.8 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-90AT | 90 | 0.8 | 6.5-19.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-90AT | 90 | 1 | 5.4-16.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-90AT | 90 | 1.25 | 4.2-15.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-110AT | 110 | 0.8 | 7.9-23.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-110AT | 110 | 1 | 6.5-19.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-110AT | 110 | 1.25 | 6.2-18.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-132AT | 132 | 0.8 | 9.2-27.2 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-132AT | 132 | 1 | 7.9-23.2 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-132AT | 132 | 1.25 | 6.8-20.1 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-160AT | 160 | 0.8 | 11.3-33.3 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-160AT | 160 | 1 | 9.8-28.8 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-160AT | 160 | 1.25 | 7.4-27.6 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-185AT | 185 | 0.8 | 13.5-39.7 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-185AT | 185 | 1 | 11.3-33.3 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-185AT | 185 | 1.25 | 10.4-30.7 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-200AT | 200 | 0.8 | 14.6-43.1 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-200AT | 200 | 1 | 13.4-39.5 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-200AT | 200 | 1.25 | 10.7-31.6 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-220AT | 220 | 0.8 | 15.5-45.5 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-220AT | 220 | 1 | 14.3-42.0 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-220AT | 220 | 1.25 | 12.1-35.7 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-250AT | 250 | 0.8 | 18.4-54.0 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-250AT | 250 | 1 | 16.1-47.4 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-250AT | 250 | 1.25 | 14.2-41.8 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-280AT | 280 | 0.8 | 19.6-57.8 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-280AT | 280 | 1 | 17.3-50.9 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-280AT | 280 | 1.25 | 14.3-42.2 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-315AT | 315 | 0.8 | 21.7-63.9 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-315AT | 315 | 1 | 19.6-57.6 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-315AT | 315 | 1.25 | 16.0-47.0 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-355AT | 355 | 0.8 | 25.9-76.4 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-355AT | 355 | 1 | 20.8-61.2 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-355AT | 355 | 1.25 | 18.1-53.1 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-400AT | 400 | 0.8 | 28.5-81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400AT | 400 | 1 | 26.0-76.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400AT | 400 | 1.25 | 21.0-61.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-450AT | 450 | 0.8 | 32.0-91.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450AT | 450 | 1 | 28.0-81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450AT | 450 | 1.25 | 25.0-75.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-7.5J | 7.5 | 0.8 | 1.1 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 170 | — | — | |
| SH-7.5J | 7.5 | 1 | 0.9 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 170 | — | — | |
| SH-7.5J | 7.5 | 1.25 | 0.8 | 62±2 | Air-cooled | G1/2 | 1000×650×850 | 170 | — | — | |
| SH-11J | 11 | 0.8 | 1.7 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 280 | — | — | |
| SH-11J | 11 | 1 | 1.6 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 280 | — | — | |
| SH-11J | 11 | 1.25 | 1.1 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 280 | — | — | |
| SH-15J | 15 | 0.8 | 2.4 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 320 | — | — | |
| SH-15J | 15 | 1 | 2.1 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 320 | — | — | |
| SH-15J | 15 | 1.25 | 1.7 | 62±2 | Air-cooled | G3/4 | 1100×750×1000 | 320 | — | — | |
| SH-22J | 22 | 0.8 | 3.6 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 400 | — | — | |
| SH-22J | 22 | 1 | 3.5 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 400 | — | — | |
| SH-22J | 22 | 1.25 | 2.7 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 400 | — | — | |
| SH-30J | 30 | 0.8 | 5.0 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 410 | — | — | |
| SH-30J | 30 | 1 | 3.5 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 410 | — | — | |
| SH-30J | 30 | 1.25 | 3.3 | 65±2 | Air-cooled | G1 | 1300×840×1175 | 410 | — | — | |
| SH-37J | 37 | 0.8 | 6.2 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 620 | — | — | |
| SH-37J | 37 | 1 | 5.0 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 620 | — | — | |
| SH-37J | 37 | 1.25 | 4.8 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 620 | — | — | |
| SH-45J | 45 | 0.8 | 7.1 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 715 | — | — | |
| SH-45J | 45 | 1 | 5.8 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 715 | — | — | |
| SH-45J | 45 | 1.25 | 5.6 | 68±2 | Air-cooled (axial fan) | G1 1/2 | 1400×1000×1320 | 715 | — | — | |
| SH-55J | 55 | 0.8 | 9.3 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1040 | — | — | |
| SH-55J | 55 | 1 | 6.9 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1040 | — | — | |
| SH-55J | 55 | 1.25 | 6.7 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1040 | — | — | |
| SH-75J | 75 | 0.8 | 12.2 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1100 | — | — | |
| SH-75J | 75 | 1 | 9.2 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1100 | — | — | |
| SH-75J | 75 | 1.25 | 9.0 | 72±2 | Air-cooled (axial fan) | G2 | 1750×1220×1600 | 1100 | — | — | |
| SH-90J | 90 | 0.8 | 15.4 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-90J | 90 | 1 | 11.2 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-90J | 90 | 1.25 | 11.0 | 75±2 | Air-cooled (axial fan) | G2 | 1900×1300×1600 | 1150 | — | — | |
| SH-110J | 110 | 0.8 | 19.0 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-110J | 110 | 1 | 14.3 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-110J | 110 | 1.25 | 14.0 | 75±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1800 | — | — | |
| SH-132J | 132 | 0.8 | 22.3 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-132J | 132 | 1 | 18.7 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-132J | 132 | 1.25 | 18.5 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2100×1400×1880 | 1830 | — | — | |
| SH-160J | 160 | 0.8 | 28.0 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-160J | 160 | 1 | 21.2 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-160J | 160 | 1.25 | 21.0 | 78±2 | Air-cooled (axial fan) | G2 1/2 | 2400×1500×2035 | 2150 | — | — | |
| SH-185J | 185 | 0.8 | 30.8 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-185J | 185 | 1 | 27.0 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-185J | 185 | 1.25 | 21.2 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 2700/2620 | — | — | |
| SH-200J* | 200 | 0.8 | 34.5* | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-200J* | 200 | 1 | 30.6 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-200J* | 200 | 1.25 | 27.0 | 80±2 | Air / water cooled | DN80 | 3000×1640×2150 | 3000/2920 | — | — | |
| SH-220J* | 220 | 0.8 | 38.1 | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-220J* | 220 | 1 | 31.0* | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-220J* | 220 | 1.25 | 28.8 | 80±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3600/3350 | — | — | |
| SH-250J | 250 | 0.8 | 42.0 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-250J | 250 | 1 | 30.7 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-250J | 250 | 1.25 | 30.3 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 3800/3550 | — | — | |
| SH-280J | 280 | 0.8 | 46.1 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-280J | 280 | 1 | 41.0 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-280J | 280 | 1.25 | 37.0 | 82±2 | Air / water cooled | DN125 | 3800×2250×2400 | 4000/3750 | — | — | |
| SH-15JT | 15 | 0.8 | 2.9 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-15JT | 15 | 1 | 2.4 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-15JT | 15 | 1.25 | 2.1 | 65±2 | — | G1 | 1300×790×1150 | 600 | — | — | |
| SH-22JT | 22 | 0.8 | 4.2 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-22JT | 22 | 1 | 3.5 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-22JT | 22 | 1.25 | 2.6 | 65±2 | — | G1 1/2 | 1400×950×1320 | 700 | — | — | |
| SH-30JT | 30 | 0.8 | 6.1 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-30JT | 30 | 1 | 5.2 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-30JT | 30 | 1.25 | 4.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 760 | — | — | |
| SH-37JT | 37 | 0.8 | 7.2 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-37JT | 37 | 1 | 6.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-37JT | 37 | 1.25 | 5.0 | 65±2 | — | G1 1/2 | 1580×950×1430 | 800 | — | — | |
| SH-45JT | 45 | 0.8 | 9.3 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-45JT | 45 | 1 | 8.2 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-45JT | 45 | 1.25 | 6.9 | 65±2 | — | G2 | 2000×1250×1680 | 1400 | — | — | |
| SH-55JT | 55 | 0.8 | 12.2 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-55JT | 55 | 1 | 9.3 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-55JT | 55 | 1.25 | 8.3 | 70±2 | — | G2 | 2000×1250×1680 | 1460 | — | — | |
| SH-75JT | 75 | 0.8 | 16.2 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-75JT | 75 | 1 | 13.0 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-75JT | 75 | 1.25 | 11.8 | 70±2 | — | G2 | 2000×1250×1880 | 1550 | — | — | |
| SH-90JT | 90 | 0.8 | 19.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-90JT | 90 | 1 | 16.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-90JT | 90 | 1.25 | 15.0 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2200 | — | — | |
| SH-110JT | 110 | 0.8 | 23.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-110JT | 110 | 1 | 19.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-110JT | 110 | 1.25 | 18.2 | 73±2 | — | G2 1/2 | 2400×1450×2035 | 2300 | — | — | |
| SH-132JT | 132 | 0.8 | 27.2 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-132JT | 132 | 1 | 23.2 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-132JT | 132 | 1.25 | 20.1 | 75±2 | — | G2 1/2 | 2400×1450×2035 | 2500 | — | — | |
| SH-160JT | 160 | 0.8 | 33.3 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-160JT | 160 | 1 | 28.8 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-160JT | 160 | 1.25 | 27.6 | 75±2 | — | DN80 | 3000×1590×2150 | 3000 | — | — | |
| SH-185JT | 185 | 0.8 | 39.7 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-185JT | 185 | 1 | 33.3 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-185JT | 185 | 1.25 | 30.7 | 78±2 | — | DN125 | 3800×2200×2400 | 5100/4950 | — | — | |
| SH-200JT | 200 | 0.8 | 43.1 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-200JT | 200 | 1 | 39.5 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-200JT | 200 | 1.25 | 31.6 | 78±2 | — | DN125 | 3800×2200×2400 | 5200/4950 | — | — | |
| SH-220JT | 220 | 0.8 | 45.5 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-220JT | 220 | 1 | 42.0 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-220JT | 220 | 1.25 | 35.7 | 78±2 | — | DN125 | 3800×2200×2400 | 6000/5700 | — | — | |
| SH-250JT | 250 | 0.8 | 54.0 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-250JT | 250 | 1 | 47.4 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-250JT | 250 | 1.25 | 41.8 | 80±2 | — | DN125 | 3800×2200×2400 | 6500/5800 | — | — | |
| SH-280JT | 280 | 0.8 | 57.8 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-280JT | 280 | 1 | 50.9 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-280JT | 280 | 1.25 | 42.2 | 80±2 | — | DN125 | 3800×2200×2400 | 7000/6000 | — | — | |
| SH-315JT | 315 | 0.8 | 63.9 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-315JT | 315 | 1 | 57.6 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-315JT | 315 | 1.25 | 47.0 | 82±2 | — | DN150 | 4200×2500×2800 | 8800/8000 | — | — | |
| SH-355JT | 355 | 0.8 | 76.4 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-355JT | 355 | 1 | 61.2 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-355JT | 355 | 1.25 | 53.1 | 82±2 | — | DN150 | 4200×2500×2800 | 9200/8400 | — | — | |
| SH-400JT | 400 | 0.8 | 81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400JT | 400 | 1 | 76.4 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-400JT | 400 | 1.25 | 62.2 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9100 | — | — | |
| SH-450JT | 450 | 0.8 | 91.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450JT | 450 | 1 | 81.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-450JT | 450 | 1.25 | 76.0 | 85±2 | Water cooled | DN150 | 4500×2500×2800 | 9200 | — | — | |
| SH-7.5AZ | 7.5 | 0.8 | 0.4-1.1 | 62±2 | — | G3/4 | 1140×600×1270 | 195/230/255 | 200 | 4-in-1 standard | |
| SH-7.5AZ | 7.5 | 1 | 0.3-0.9 | 62±2 | — | G3/4 | 1140×600×1270 | 195/230/255 | 200 | 4-in-1 standard | |
| SH-7.5AZ | 7.5 | 1.25 | 0.25-0.8 | 62±2 | — | G3/4 | 1140×600×1270 | 195/230/255 | 200 | 4-in-1 standard | |
| SH-7.5AZ/-5 | 7.5 | 0.8 | 0.4-1.1 | 62±2 | — | G3/4 | 1290×600×1300 | 225/250/280 | 200 | 4-in-1 standard | |
| SH-7.5AZ/-5 | 7.5 | 1 | 0.3-0.9 | 62±2 | — | G3/4 | 1290×600×1300 | 225/250/280 | 200 | 4-in-1 standard | |
| SH-7.5AZ/-5 | 7.5 | 1.25 | 0.25-0.8 | 62±2 | — | G3/4 | 1290×600×1300 | 225/250/280 | 200 | 4-in-1 standard | |
| SH-11AZ | 11 | 0.8 | 0.6-1.8 | 62±2 | — | G3/4 | 1200×730×1450 | 280/300/320 | 200 | 4-in-1 standard | |
| SH-11AZ | 11 | 1 | 0.5-1.6 | 62±2 | — | G3/4 | 1200×730×1450 | 280/300/320 | 200 | 4-in-1 standard | |
| SH-11AZ | 11 | 1.25 | 0.5-1.5 | 62±2 | — | G3/4 | 1200×730×1450 | 280/300/320 | 200 | 4-in-1 standard | |
| SH-11AZ/-5 | 11 | 0.8 | 0.6-1.8 | 62±2 | — | G3/4 | 1600×780×1620 | 380/400/415 | 400 | 4-in-1 standard | |
| SH-11AZ/-5 | 11 | 1 | 0.5-1.6 | 62±2 | — | G3/4 | 1600×780×1620 | 380/400/415 | 400 | 4-in-1 standard | |
| SH-11AZ/-5 | 11 | 1.25 | 0.5-1.5 | 62±2 | — | G3/4 | 1600×780×1620 | 380/400/415 | 400 | 4-in-1 standard | |
| SH-15AZ | 15 | 0.8 | 0.8-2.4 | 62±2 | — | G3/4 | 1200×730×1450 | 285/305/335 | 200 | 4-in-1 standard | |
| SH-15AZ | 15 | 1 | 0.7-2.2 | 62±2 | — | G3/4 | 1200×730×1450 | 285/305/335 | 200 | 4-in-1 standard | |
| SH-15AZ | 15 | 1.25 | 0.7-2.0 | 62±2 | — | G3/4 | 1200×730×1450 | 285/305/335 | 200 | 4-in-1 standard | |
| SH-15AZ/-5 | 15 | 0.8 | 0.8-2.4 | 62±2 | — | G3/4 | 1600×780×1620 | 385/420/450 | 400 | 4-in-1 standard | |
| SH-15AZ/-5 | 15 | 1 | 0.7-2.2 | 62±2 | — | G3/4 | 1600×780×1620 | 385/420/450 | 400 | 4-in-1 standard | |
| SH-15AZ/-5 | 15 | 1.25 | 0.7-2.0 | 62±2 | — | G3/4 | 1600×780×1620 | 385/420/450 | 400 | 4-in-1 standard | |
| SH-22AZ | 22 | 0.8 | 1.2-3.6 | 65±2 | — | G1 1/2 | 1900×940×1880 | 575/550/580 | 500 | 4-in-1 standard | |
| SH-22AZ | 22 | 1 | 1.1-3.2 | 65±2 | — | G1 1/2 | 1900×940×1880 | 575/550/580 | 500 | 4-in-1 standard | |
| SH-22AZ | 22 | 1.25 | 1.0-3.0 | 65±2 | — | G1 1/2 | 1900×940×1880 | 575/550/580 | 500 | 4-in-1 standard | |
| SH-30AZ | 30 | 0.8 | 1.7-5.0 | 65±2 | — | G1 1/2 | 1900×940×1880 | 540/560/590 | 500 | 4-in-1 standard | |
| SH-30AZ | 30 | 1 | 1.4-3.6 | 65±2 | — | G1 1/2 | 1900×940×1880 | 540/560/590 | 500 | 4-in-1 standard | |
| SH-30AZ | 30 | 1.25 | 1.2-3.5 | 65±2 | — | G1 1/2 | 1900×940×1880 | 540/560/590 | 500 | 4-in-1 standard | |
| SH-37AZ | 37 | 0.8 | 2.2-6.5 | 68±2 | — | G1 1/2 | 2400×990×2000 | 700/720/740 | 1000 | 4-in-1 standard | |
| SH-37AZ | 37 | 1 | 1.8-5.2 | 68±2 | — | G1 1/2 | 2400×990×2000 | 700/720/740 | 1000 | 4-in-1 standard | |
| SH-37AZ | 37 | 1.25 | 1.5-4.5 | 68±2 | — | G1 1/2 | 2400×990×2000 | 700/720/740 | 1000 | 4-in-1 standard | |
| SH-45AZ | 45 | 0.8 | 2.4-7.1 | 68±2 | — | G1 1/2 | 2400×990×2000 | 720/740/760 | 1000 | 4-in-1 standard | |
| SH-45AZ | 45 | 1 | 2.2-6.3 | 68±2 | — | G1 1/2 | 2400×990×2000 | 720/740/760 | 1000 | 4-in-1 standard | |
| SH-45AZ | 45 | 1.25 | 1.7-5.1 | 68±2 | — | G1 1/2 | 2400×990×2000 | 720/740/760 | 1000 | 4-in-1 standard | |
| SH-7.5JZ | 7.5 | 0.8 | 1.1 | 62±2 | — | G3/4 | 1140×600×1270 | 215/230/250 | 200 | 4-in-1 standard | |
| SH-7.5JZ | 7.5 | 1.0 | 0.9 | 62±2 | — | G3/4 | 1140×600×1270 | 215/230/250 | 200 | 4-in-1 standard | |
| SH-7.5JZ | 7.5 | 1.25 | 0.8 | 62±2 | — | G3/4 | 1140×600×1270 | 215/230/250 | 200 | 4-in-1 standard | |
| SH-11JZ | 11 | 0.8 | 1.7 | 62±2 | — | G3/4 | 1600×780×1620 | 420/450/480 | 400 | 4-in-1 standard | |
| SH-11JZ | 11 | 1.0 | 1.6 | 62±2 | — | G3/4 | 1600×780×1620 | 420/450/480 | 400 | 4-in-1 standard | |
| SH-11JZ | 11 | 1.25 | 1.1 | 62±2 | — | G3/4 | 1600×780×1620 | 420/450/480 | 400 | 4-in-1 standard | |
| SH-15JZ | 15 | 0.8 | 2.4 | 62±2 | — | G3/4 | 1600×780×1620 | 425/455/485 | 400 | 4-in-1 standard | |
| SH-15JZ | 15 | 1.0 | 2.1 | 62±2 | — | G3/4 | 1600×780×1620 | 425/455/485 | 400 | 4-in-1 standard | |
| SH-15JZ | 15 | 1.25 | 1.7 | 62±2 | — | G3/4 | 1600×780×1620 | 425/455/485 | 400 | 4-in-1 standard | |
| SH-22JZ | 22 | 0.8 | 3.6 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-22JZ | 22 | 1.0 | 3.5 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-22JZ | 22 | 1.25 | 2.7 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-30JZ | 30 | 0.8 | 5.0 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-30JZ | 30 | 1.0 | 3.5 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-30JZ | 30 | 1.25 | 3.3 | 65±2 | — | G1 1/2 | 1900×940×1880 | 550/580/600 | 500 | 4-in-1 standard | |
| SH-37JZ | 37 | 0.8 | 6.2 | 68±2 | — | G1 1/2 | 2400×990×2000 | 750/770/790 | 1000 | 4-in-1 standard | |
| SH-37JZ | 37 | 1.0 | 5.0 | 68±2 | — | G1 1/2 | 2400×990×2000 | 750/770/790 | 1000 | 4-in-1 standard | |
| SH-37JZ | 37 | 1.25 | 4.8 | 68±2 | — | G1 1/2 | 2400×990×2000 | 750/770/790 | 1000 | 4-in-1 standard | |
| SH-45JZ | 45 | 0.8 | 7.1 | 68±2 | — | G1 1/2 | 2400×990×2000 | 770/790/810 | 1000 | 4-in-1 standard | |
| SH-45JZ | 45 | 1.0 | 5.8 | 68±2 | — | G1 1/2 | 2400×990×2000 | 770/790/810 | 1000 | 4-in-1 standard | |
| SH-45JZ | 45 | 1.25 | 5.6 | 68±2 | — | G1 1/2 | 2400×990×2000 | 770/790/810 | 1000 | 4-in-1 standard | |
| SH-7.5AZG | 7.5 | 1.25 | 0.24-0.7 | 62±2 | — | G3/4 | 1140×600×1270 | 220 | 200 | 4-in-1 high-spec | |
| SH-11AZG | 11 | 1.55 | 0.33-1.0 | 62±2 | — | G3/4 | 1600×780×1520 | 390 | 400 | 4-in-1 high-spec | |
| SH-15AZG | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1600×780×1520 | 400 | 400 | 4-in-1 high-spec | |
| SH-15AZG | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1600×780×1320 | 395 | 400 | 4-in-1 high-spec | |
| SH-22AZG | 22 | 1.55 | 0.8-2.3 | 65±2 | — | G1 | 1600×780×1620 | 465 | 400 | 4-in-1 high-spec | |
| SH-37AZG | 37 | 1.55 | 1.2-3.3 | 65±2 | — | G1 1/2 | 1900×940×1880 | 645 | 500 | 4-in-1 high-spec | |
| SH-15AZGX | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1900×780×1860 | 520 | 500 | 5-in-1 high-spec | |
| SH-22AZGX | 22 | 1.55 | 0.8-2.3 | 65±2 | — | G1 | 1900×780×2120 | 560 | 500 | 5-in-1 high-spec | |
| SH-37AZGX | 37 | 1.55 | 1.2-3.3 | 65±2 | — | G1 1/2 | 2400×940×2200 | 830 | 1000 | 5-in-1 high-spec | |
| SH-7.5JZG | 7.5 | 1.25 | 0.24-0.7 | 62±2 | — | G3/4 | 1140×600×1270 | 240 | 200 | 4-in-1 high-spec | |
| SH-11JZG | 11 | 1.55 | 0.33-1.0 | 62±2 | — | G3/4 | 1600×780×1520 | 410 | 400 | 4-in-1 high-spec | |
| SH-15JZG | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1600×780×1520 | 420 | 400 | 4-in-1 high-spec | |
| SH-15JZG* | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1600×780×1320 | 415 | 400 | Export version | |
| SH-22JZG | 22 | 1.55 | 0.8-2.3 | 65±2 | — | G1 | 1600×780×1620 | 490 | 400 | 4-in-1 high-spec | |
| SH-37JZG | 37 | 1.55 | 1.2-3.3 | 65±2 | — | G1 1/2 | 1900×940×1880 | 680 | 500 | 4-in-1 high-spec | |
| SH-15JZGX | 15 | 1.55 | 0.46-1.3 | 62±2 | — | G3/4 | 1900×780×1860 | 540 | 500 | 5-in-1 high-spec | |
| SH-22JZGX | 22 | 1.55 | 0.8-2.3 | 65±2 | — | G1 | 1900×780×2120 | 590 | 500 | 5-in-1 high-spec | |
| SH-37JZGX | 37 | 1.55 | 1.2-3.3 | 65±2 | — | G1 1/2 | 2400×940×2200 | 860 | 1000 | 5-in-1 high-spec | |
| SH-45JZGX | 45 | 1.55 | 1.6-4.5 | 65±2 | — | G1 1/2 | 2400×940×2200 | 900 | 1000 | 5-in-1 high-spec | |
| SH-22ADH-2 | 22 | 0.2 | 2.8-8.0 | 65±3 | Air-cooled (centrifugal fan) | G2 | 2200×1340×1800 | — | — | — | |
| SH-22ADH-3 | 22 | 0.3 | 2.2-6.0 | 65±3 | Air-cooled (centrifugal fan) | G2 | 1400×1000×1510 | — | — | — | |
| SH-22ADHT-4 | 22 | 0.4 | 2.0-5.8 | 65±3 | Air-cooled (centrifugal fan) | G2 | 1400×1000×1510 | — | — | — | |
| SH-22ADHT-5 | 22 | 0.5 | 1.9-5.5 | 65±3 | Air-cooled (centrifugal fan) | G2 | 1400×1000×1510 | — | — | — | |
| SH-30ADH-2 | 30 | 0.2 | 4.0-11.4 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-30ADH-3 | 30 | 0.3 | 2.9-8.4 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-30ADHT-4 | 30 | 0.4 | 2.9-8.2 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-30ADHT-5 | 30 | 0.5 | 2.7-7.8 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-37ADH-2 | 37 | 0.2 | 5.1-14.6 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-37ADH-3 | 37 | 0.3 | 3.9-11.2 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-37ADHT-4 | 37 | 0.4 | 3.6-10.4 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-37ADHT-5 | 37 | 0.5 | 3.2-9.4 | 65±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-45ADH-2 | 45 | 0.2 | 5.8-16.6 | 68±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-45ADH-3 | 45 | 0.3 | 5.0-14.3 | 68±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-45ADHT-4 | 45 | 0.4 | 4.3-12.5 | 68±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-45ADHT-5 | 45 | 0.5 | 4.1-11.7 | 68±3 | Air-cooled (centrifugal fan) | G3/DN80 | 2200×1340×1800 | — | — | — | |
| SH-55ADH-2 | 55 | 0.2 | 7.4-21.2 | 68±3 | Air-cooled (centrifugal fan) | DN100 | 2400×1570×1900 | — | — | — | |
| SH-55ADH-3 | 55 | 0.3 | 6.4-18.3 | 68±3 | Air-cooled (centrifugal fan) | DN100 | 2400×1570×1900 | — | — | — | |
| SH-55ADHT-4 | 55 | 0.4 | 5.9-17.0 | 68±3 | Air-cooled (centrifugal fan) | DN100 | 2400×1570×1900 | — | — | — | |
| SH-55ADHT-5 | 55 | 0.5 | 5.5-15.8 | 68±3 | Air-cooled (centrifugal fan) | DN100 | 2400×1570×1900 | — | — | — | |
| SH-75ADH-2 | 75 | 0.2 | 10.6-30.4 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-75ADH-3 | 75 | 0.3 | 8.7-25.1 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 2400×1570×1900 | — | — | — | |
| SH-75ADHT-4 | 75 | 0.4 | 7.1-20.6 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 2400×1570×1900 | — | — | — | |
| SH-75ADHT-5 | 75 | 0.5 | 6.6-19.6 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 2400×1570×1900 | — | — | — | |
| SH-90ADH-2 | 90 | 0.2 | 13.1-37.5 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-90ADH-3 | 90 | 0.3 | 10.5-30.2 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-90ADHT-4 | 90 | 0.4 | 8.9-25.4 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 2400×1570×1900 | — | — | — | |
| SH-90ADHT-5 | 90 | 0.5 | 8.1-23.3 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 2400×1570×1900 | — | — | — | |
| SH-110ADH-2 | 110 | 0.2 | 16.9-48.3 | 70±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-110ADH-3 | 110 | 0.3 | 13.1-37.5 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-110ADHT-4 | 110 | 0.4 | 10.6-30.4 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-110ADHT-5 | 110 | 0.5 | 9.9-28.3 | 70±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-132ADH-2 | 132 | 0.2 | 20.0-57.0 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-132ADH-3 | 132 | 0.3 | 16.0-45.7 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-132ADHT-4 | 132 | 0.4 | 14.0-40.0 | 72±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-132ADHT-5 | 132 | 0.5 | 12.7-36.2 | 72±3 | Air-cooled (centrifugal fan) | DA100 | 3180×1690×2150 | — | — | — | |
| SH-160ADH-2 | 160 | 0.2 | 22.8-65.3 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-160ADH-3 | 160 | 0.3 | 18.6-53.3 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-160ADHT-4 | 160 | 0.4 | 15.6-47.1 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-160ADHT-5 | 160 | 0.5 | 12.9-43.0 | 72±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-185ADH-2 | 185 | 0.2 | 24.4-69.9 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-185ADH-3 | 185 | 0.3 | 21.8-62.4 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-185ADHT-4 | 185 | 0.4 | 16.7-49.8 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-185ADHT-5 | 185 | 0.5 | 15.1-46.0 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-200ADH-2 | 200 | 0.2 | 26.6-76.0 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-200ADH-3 | 200 | 0.3 | 23.4-67.0 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-200ADHT-4 | 200 | 0.4 | 18.8-53.7 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-200ADHT-5 | 200 | 0.5 | 16.5-47.6 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4000×2250×2400 | — | — | — | |
| SH-220ADH-2 | 220 | 0.2 | 29.9-85.4 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-220ADH-3 | 220 | 0.3 | 26.2-75.1 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-220ADHT-4 | 220 | 0.4 | 21.6-61.7 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-220ADHT-5 | 220 | 0.5 | 20.3-54.2 | 75±3 | Air-cooled (centrifugal fan) | DN150 | 4400×2540×2800 | — | — | — | |
| SH-22AD-2 | 22 | 0.2 | 2.8-8.0 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-22AD-3 | 22 | 0.3 | 2.2-6.0 | 67±3 | Air-cooled (axial fan) | G2 | 1400×1000×1320 | — | — | — | |
| SH-22ADT-4 | 22 | 0.4 | 2.0-5.8 | 67±3 | Air-cooled (axial fan) | G2 | 1400×1000×1320 | — | — | — | |
| SH-22ADT-5 | 22 | 0.5 | 1.9-5.5 | 67±3 | Air-cooled (axial fan) | G2 | 1400×1000×1320 | — | — | — | |
| SH-30AD-2 | 30 | 0.2 | 4.0-11.4 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-30AD-3 | 30 | 0.3 | 2.9-8.4 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-30ADT-4 | 30 | 0.4 | 2.9-8.2 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-30ADT-5 | 30 | 0.5 | 2.7-7.8 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-37AD-2 | 37 | 0.2 | 5.1-14.6 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1900×1300×1600 | — | — | — | |
| SH-37AD-3 | 37 | 0.3 | 3.9-11.2 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-37ADT-4 | 37 | 0.4 | 3.6-10.4 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-37ADT-5 | 37 | 0.5 | 3.2-9.4 | 67±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-45AD-2 | 45 | 0.2 | 5.8-16.6 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1900×1300×1600 | — | — | — | |
| SH-45AD-3 | 45 | 0.3 | 5.0-14.3 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1900×1300×1600 | — | — | — | |
| SH-45ADT-4 | 45 | 0.4 | 4.3-12.5 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-45ADT-5 | 45 | 0.5 | 4.1-11.7 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1750×1220×1600 | — | — | — | |
| SH-55AD-2 | 55 | 0.2 | 7.4-21.2 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 2100×1400×1880 | — | — | — | |
| SH-55AD-3 | 55 | 0.3 | 6.4-18.3 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 2100×1400×1880 | — | — | — | |
| SH-55ADT-4 | 55 | 0.4 | 5.9-17.0 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1900×1300×1600 | — | — | — | |
| SH-55ADT-5 | 55 | 0.5 | 5.5-15.8 | 70±3 | Air-cooled (axial fan) | G3/DN80 | 1900×1300×1600 | — | — | — | |
| SH-75AD-2 | 75 | 0.2 | 10.6-30.4 | 72±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-75AD-3 | 75 | 0.3 | 8.7-25.1 | 72±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-75ADT-4 | 75 | 0.4 | 7.1-20.6 | 72±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-75ADT-5 | 75 | 0.5 | 6.6-19.6 | 72±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-90AD-2 | 90 | 0.2 | 13.1-37.5 | 75±3 | Air-cooled (axial fan) | DA100 | 3000×1640×2150 | — | — | — | |
| SH-90AD-3 | 90 | 0.3 | 10.5-30.2 | 75±3 | Air-cooled (axial fan) | DA100 | 3000×1640×2150 | — | — | — | |
| SH-90ADT-4 | 90 | 0.4 | 8.9-25.4 | 75±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-90ADT-5 | 90 | 0.5 | 8.1-23.3 | 75±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-110AD-2 | 110 | 0.2 | 16.9-48.3 | 75±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-110AD-3 | 110 | 0.3 | 13.1-37.5 | 75±3 | Air-cooled (axial fan) | DA100 | 3000×1640×2150 | — | — | — | |
| SH-110ADT-4 | 110 | 0.4 | 10.6-30.4 | 75±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-110ADT-5 | 110 | 0.5 | 9.9-28.3 | 75±3 | Air-cooled (axial fan) | DA100 | 2400×1500×2035 | — | — | — | |
| SH-132AD-2 | 132 | 0.2 | 20.0-57.0 | 78±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-132AD-3 | 132 | 0.3 | 16.0-45.7 | 78±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-132ADT-4 | 132 | 0.4 | 14.0-40.0 | 78±3 | Air-cooled (axial fan) | DA100 | 3000×1640×2150 | — | — | — | |
| SH-132ADT-5 | 132 | 0.5 | 12.7-36.2 | 78±3 | Air-cooled (axial fan) | DA100 | 3000×1640×2150 | — | — | — | |
| SH-160AD-2 | 160 | 0.2 | 22.8-65.3 | 78±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-160AD-3 | 160 | 0.3 | 18.6-53.3 | 78±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-160ADT-4 | 160 | 0.4 | 15.6-47.1 | 78±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-160ADT-5 | 160 | 0.5 | 12.9-43.0 | 78±3 | Air-cooled (axial fan) | DN150 | 3000×1640×2150 | — | — | — | |
| SH-185AD-2 | 185 | 0.2 | 24.4-69.9 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-185AD-3 | 185 | 0.3 | 21.8-62.4 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-185ADT-4 | 185 | 0.4 | 16.7-49.8 | 80±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-185ADT-5 | 185 | 0.5 | 15.1-46.0 | 80±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-200AD-2 | 200 | 0.2 | 26.6-76.0 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-200AD-3 | 200 | 0.3 | 23.4-67.0 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-200ADT-4 | 200 | 0.4 | 18.8-53.7 | 80±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-200ADT-5 | 200 | 0.5 | 16.5-47.6 | 80±3 | Air-cooled (axial fan) | DN150 | 3800×2250×2400 | — | — | — | |
| SH-220AD-2 | 220 | 0.2 | 29.9-85.4 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-220AD-3 | 220 | 0.3 | 26.2-75.1 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-220ADT-4 | 220 | 0.4 | 21.6-61.7 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — | |
| SH-220ADT-5 | 220 | 0.5 | 20.3-54.2 | 80±3 | Air-cooled (axial fan) | DN150 | 4200×2500×2800 | — | — | — |
- Capacities are FAD ranges at the listed working pressure; fixed-speed models show rated FAD.
- Weights shown as A/B refer to air-cooled / water-cooled versions; combined-station weights vary with dryer configuration.
- 4-in-1 = compressor + receiver + refrigerated dryer + filters; 5-in-1 adds an extra treatment stage. Laser-cutting packages are rated 1.25–1.55 MPa.
- Parameters are for reference and may be updated without notice; the order technical agreement prevails.
Industries served
Where DLOL industrial air works
Food & beveragePharmaceuticalTextileElectronics
MachineryPrintingChemicalMining
Laser cuttingAeration & conveyingPower plantsNew energy
OEM and ODM programmes are available for distributors and system integrators; machines can be branded and configured to your market.